Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
How do you really feel about How to Install a Bathtub Yourself?
Mounting a bathtub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is readily obtainable, the project can relocate easily; if you have to open up a wall surface to get rid of the old bathtub as well as position the new tub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and also embeded in the new one. Ensure you have actually qualified yourself for the task and also fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will certainly help you mount a brand-new tub in your washroom if you have actually already purchased a brand-new bathtub as well as don't need to transform the setup of your previous supply of water pipes.
Your devices and material list need to comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome because of the limited accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Secure the faucet in place with the supplier supplied backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Tub
Utilizing both wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the bath tub until the spirit level reviews degree.
To install taps, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water supply as well as inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bathtub and also check the overflow outlet and the typical outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub ought to wait till the tub has actually been utilized at least once as this will settle it into its last placement.
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealer can fracture rather very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads about How to Install a Bathtub, I think sharing that short article was a great idea. Enjoyed our post? Please share it. Let other people find it. Thanks for taking the time to read it.
Water trouble? Dial. Report this page